📋 About this paper
- Exam
- Grade 12 Model Examination (Physics)
- Subject
- PHYSICS
- Sitting
- Second semester · 2nd round · 2018 E.C. (2026 G.C.)
- Time allowed
- 2 hours 30 minutes
- Questions
- 60
- Region
- Addis Ababa
- Stream
- Natural Science
- Round
- Second semester · 2nd round
Exam directions
- This booklet contains the Physics model examination. This examination consists of a total of 60 multiple choice questions.
- Carefully select the best answer and write the letter of your choice on the separate answer sheet provided.
- Follow the instructions on both the answer sheet and the examination paper carefully.
- Please do not write unnecessary marks on the answer sheet.
- You are allowed to work on the examination for 2 hours 30 minutes. When time is called, you must immediately stop working, put your pen down, and wait for further instructions.
- Any form of cheating or an attempt to cheat during the examination will result in automatic dismissal from the examination hall and cancellation of your score(s).
- Please make sure that you have written all the required information on the answer sheet before you begin working on the examination.
- Useful data: g = 10 m/s²; μ₀ = 4π × 10⁻⁷ T·m/A; ε₀ = 8.85 × 10⁻¹² F/m; k = 9 × 10⁹ N·m²/C²; mass of proton = 1.67 × 10⁻²⁷ kg; mass of electron = 9.11 × 10⁻³¹ kg; elementary charge = ±1.6 × 10⁻¹⁹ C; density of water = 1000 kg/m³; sin 30° = cos 60° = 0.5; sin 20° = 0.34; cos 20° = 0.94; sin 60° = cos 30° = 0.87; sin 45° = cos 45° = 0.707.
Part I: Multiple Choice
Carefully select the best answer and write the letter of your choice on the separate answer sheet provided.
- 1
When an object moves along a curved path between two points, the distance traveled is usually greater than the displacement because:
- ADistance measures the shortest path.
- BDisplacement measures the total path length.
- CDistance always equals displacement.
- DDistance measures the entire path traveled while displacement measures the shortest straight line.
Show answer
D Distance measures the entire path traveled while displacement measures the shortest straight line.
Distance is the full length of the path actually travelled, while displacement is the straight-line separation from start to finish. On a curved path the straight line is shorter, so distance exceeds displacement. A and B swap the two definitions.
- 2
During a journey, the velocity of a moving object may change continuously due to acceleration or deceleration. Which of the following quantities helps describe the velocity of the object at a specific moment during such motion?
- AAverage velocity
- BInstantaneous velocity
- CTotal displacement
- DAverage speed
Show answer
B Instantaneous velocity
Instantaneous velocity is the velocity at one particular instant (the slope of the position–time graph at that moment). Average velocity and average speed describe a whole time interval, not a single moment.
- 3
Which of the following statements correctly defines uniform motion?
- AMotion in which an object covers equal distances in equal intervals of time
- BMotion in which an object changes its speed continuously
- CMotion in which the object stops after some time
- DMotion in which the object changes direction frequently
Show answer
A Motion in which an object covers equal distances in equal intervals of time
Uniform motion means constant speed: equal distances are covered in equal intervals of time, however small. Changing speed (B) is non-uniform motion.
- 4
The motion of a circus clown on a unicycle moving in a straight line is shown in the graph below. After 12 seconds, how far is the clown from her original starting point?
- A0 m
- B10 m
- C47 m
- D74 m
Show answer
D 74 m
Displacement is the area under the velocity–time graph, and the velocity is never negative. Areas: 0–2 s: ½×2×6 = 6 m; 2–4 s: 2×6 = 12 m; 4–6 s: ½(6+10)×2 = 16 m; 6–8 s: 2×10 = 20 m; 8–12 s: ½×4×10 = 20 m. Total = 74 m.
- 5
Which of the following examples represents a force acting without direct contact between objects?
- AA person pushing a table
- BA hammer hitting a nail
- CA magnet attracting small iron pieces
- DA hand pulling a rope
Show answer
C A magnet attracting small iron pieces
Magnetic force is a field (non-contact) force: the magnet pulls the iron pieces across a gap. Pushing, hitting and pulling a rope all need physical contact.
- 6
A student applies a force to push a heavy wooden box across the floor, but the box moves very slowly compared to a lighter box pushed with the same force. Which of the following explanations best accounts for this observation?
- AAcceleration decreases when the mass of the object increases for the same force
- BHeavier objects always move faster
- CForce has no effect on heavy objects
- DDistance traveled determines acceleration
Show answer
A Acceleration decreases when the mass of the object increases for the same force
By Newton's second law a = F/m, so for the same force a larger mass gets a smaller acceleration and picks up speed more slowly.
- 7
A boy is rolling a 0.5 kg ball on the frictionless floor with the speed of 20 m/s. The ball gets deflected by an obstacle on the way. After deflection it moves with 5 % of its initial kinetic energy. What is the speed of the ball now?
- A19 m/s
- B14.4 m/s
- C4.47 m/s
- D1 m/s
Show answer
C 4.47 m/s
Kinetic energy is proportional to v², so v_new = v·√0.05 = 20 × 0.2236 ≈ 4.47 m/s. (Check: initial KE = ½×0.5×20² = 100 J; 5 % is 5 J, and ½×0.5×v² = 5 gives v = √20 ≈ 4.47 m/s.) 1 m/s would be 5 % of the speed, not of the energy.
- 8
A ramp is used to push a heavy box into the back of a truck. Instead of lifting the box vertically, the worker pushes it along the inclined surface. The ramp makes the work easier mainly because it:
- AReduces the distance moved by the box
- BChanges the direction of motion only
- CIncreases the mass of the object
- DReduces the force needed by increasing the distance over which the force is applied
Show answer
D Reduces the force needed by increasing the distance over which the force is applied
An inclined plane is a simple machine: the work needed (about mgh) is the same, but it is spread over the longer slope length, so a smaller force is required. It increases, not reduces, the distance moved.
- 9
A simple wheel and axle is used to lift a 30 N bucket of water out of a well. The radii of the wheel and axle are 20 cm and 5 cm, respectively. If the effort required is 10 N, what is the efficiency of the machine?
- A75 %
- B60 %
- C80 %
- D90 %
Show answer
A 75 %
Mechanical advantage MA = load/effort = 30/10 = 3. Velocity ratio VR = R_wheel/r_axle = 20/5 = 4. Efficiency = MA/VR × 100 % = 3/4 × 100 % = 75 %.
- 10
A person uses a long lever to lift a heavy rock. The effort applied at the end of the lever moves through a relatively large distance while the rock moves a much shorter distance. Which of the following best describes the primary purpose of the lever in this case?
- AIt acts as a speed (distance) multiplier, allowing the effort to move a large distance
- BIt acts as a force multiplier, allowing a small effort to lift a heavy load
- CIt reduces the work done by eliminating gravity
- DIt acts as a direction changer to move the rock horizontally
Show answer
B It acts as a force multiplier, allowing a small effort to lift a heavy load
When the effort moves a large distance and the load a small one, the lever trades distance for force: a small effort produces a large force on the rock, so it is a force multiplier. A lever never reduces the work done (C).
Sit the whole paper with a timer, get your score, and read every answer explained.